MacPro_Early2008_MemoryRiserCard-DIY.pdf

(448 KB) Pobierz
 Mac Pro
Memory Riser Card
Replacement Instructions
Follow the instructions in this document carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Tools Required
No tools are required for this procedure.
Opening the Computer
1.
Shut down the computer.
Warning: Always shut down the computer before opening it to avoid damaging its
internal components or the components you are installing. Do not open the computer
or attempt to install items inside it while it is on.
Wait 5 to 10 minutes to allow the computer’s internal components to cool.
Warning: After you shut down the system, the internal components can be very hot. You
must let the computer cool down before continuing.
Unplug all external cables from the computer except the power cord.
Touch the metal PCI access covers on the back of the computer to discharge any static
electricity from your body.
Important: Always discharge static before you touch any parts or install any
components inside the computer. To avoid generating static electricity, do not walk
around the room until you have finished working and closed the computer.
2.
3.
4.
© 2008 Apple Inc. All rights reserved.
073-1180 Rev. A
1
5.
6.
Unplug the power cord.
Hold the side access panel and lift the latch on the back of the computer.
Warning: The edges of the access panel and the enclosure can be sharp. Be very careful
when handling them.
Remove the access panel and place it on a flat surface covered by a soft, clean cloth.
7.
© 2008 Apple Inc. All rights reserved.
073-1180 Rev. A
2
Removing the Installed Memory Riser Card
1.
2.
Carefully lay the computer on its side so that the open side faces up.
Locate the memory riser card.
3.
Holding the memory riser card by the two finger holes, pull it out of the memory cage and
place the card DIMM-side-up on a soft, clean cloth.
© 2008 Apple Inc. All rights reserved.
073-1180 Rev. A
3
Installing the Replacement Memory Riser Card
Warning: FB-DIMMs carry heatsinks on either side of the DIMM. Never attempt to remove
the heatsinks from the DIMMs. Doing so could damage the DIMM.
1.
Transfer each FB-DIMMs installed on the original memory riser card to the corresponding slot
on the replacement riser card. For each installed DIMM, do the following:
•
Open the ejectors for the DIMM slot on the original riser card by pushing them out to
the sides, and remove the FB-DIMM from the card.
•
Align the DIMM in the corresponding slot on the replacement riser card and push both
ends of the DIMM down until the ejectors snap back up into place.
© 2008 Apple Inc. All rights reserved.
073-1180 Rev. A
4
2.
Insert the replacement riser card into position in the memory cage, pushing slightly until the
card is seated in its logic board memory slot.
Closing the Computer
1.
Replace the access panel.
Note:
Make sure the latch is in the up position before replacing the access panel. If the latch
is down, the access panel will not seat correctly in the enclosure.
Push the latch down to close and secure the access panel.
Warning: Never turn on the computer unless all of its internal and external parts are
in place and it is closed. Operating the computer when it is open or missing parts can
damage it or cause injury.
2.
 Apple Inc.
© 2008 Apple Inc. All rights reserved.
This document is protected under U.S. Copyright Law and International Treaties, and no part of
this document may be reproduced in any form without written permission from Apple.
Apple is not responsible for typographical, printing, or inadvertent errors.
Apple Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
USA
+ 1 408 996 1010
www.apple.com
Apple, the Apple logo, and Mac are trademarks of Apple Inc., registered in the U.S. and other
countries.
© 2008 Apple Inc. All rights reserved.
073-1180 Rev. A
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin